This project is developed by keeping Malls in our minds. As shopping mall is a global phenomenon that has its roots in ancient outdoor bazaars, where people would go, buy goods, Spend free time. Not only has the shopping mall become a place to find and purchase goods, it is also known as a cultural hot spot where people of all ages can come to interact. And we know that malls consume a lot of energy. So to overcome this we have developed a fully automated project with the help of PLC every process in this mall is automated. For explain from very beginning the parking system of this mall is automatic, the door of parking will open and close automatically until parking is full. When parking will full, buzzer will beep. Elevator is present to take customer from basement parking. Doors of mall are automated. ACs of mall are automatic adjustable according to temperature. The lights of mall are also automatic. Lights gets off when no one inside the mall.
-
Technologies Covered
Analog & Digital Sensors, Electrical thesis Projects , Featured Projects, PLC & SCADA
-
Related Keywords
Industrial Automation, PLC, Control System, Process Instrumentaion, SCADA, Power Electronics, Robotic Arm, Artificial Limb, Automated Lift, Elevator, Pulley, Carparking, Transducer, Digital Sensor, Automation, Analog Sensors, Robot, Robotics, Featured Projects, Starred Projects, Exciting Projects, Electrical, Instrumentation, Power Engineering, Power Generation, Digital Sensors, Transducers, Sensing Units
Related Projects
-
Very Large Scale Integration (VLSI)
This is a process of stemming or creating integrated circuits by combing several thousands of transistors together on a single chip. VLSI stands for very large scale integration which in short has a purpose of integrating several numbers of semiconductors on a single chip. There are various VLSI technologies used as 45nm, 65nm. They have been named so depending on the length of the gate used in the transistors. A microprocessor is also a VLSI device. Structured VLSI design is a modular methodology originated just with an aim of saving microchip area by minimizing the interconnection area.
Read More -
VLSI using CPLD and FPGA
This is a process of stemming or creating integrated circuits by combing several thousands of transistors together on a single chip. VLSI stands for very large scale integration which in short has a purpose of integrating several numbers of semiconductors on a single chip. There are various VLSI technologies used as 45nm, 65nm. They have been named so depending on the length of the gate used in the transistors. A microprocessor is also a VLSI device. Structured VLSI design is a modular methodology originated just with an aim of saving microchip area by minimizing the interconnection area.
Read More -
Industrial Automation
The word “Industrial automation” implies automatically working organizations, which make use programmable logic controllers (PLC). Process control is a branched statistics and engineering discipline that deals with various controlling methods of output for a specific industrial automated process (architecture, controlling). It was a replacement invented the systems that required numbers of timers; relays etc and increase the cost also. PLCs are a combine package of multiple inputs and outputs, operating under various temperature ranges, even have immunity to noise. As the enhancements made year and year over, sequential relay control, motion control, process control, distributed control systems and networking are included into PLC. The main difference from other computers is that PLCs operate in industrial environments and have multiple (I/O) terminals; those connect the PLC to sensors and actuators. PLCs measure, continuously varied analog input process variables (P, T), and outputs t
Read More -
Industrial Automation using PLC, SCADA, HMI and Drives
The word “Industrial automation” implies automatically working organizations, which make use programmable logic controllers (PLC). Process control is a branched statistics and engineering discipline that deals with various controlling methods of output for a specific industrial automated process (architecture, controlling). It was a replacement invented the systems that required numbers of timers; relays etc and increase the cost also. SCADA is Supervisory Control and Data Acquisition is the systems used to control and Monitor small number of Equipments. They are basically used to perform data collection. It is a collection of HMI (human–machine interface) lock-out tag-out, Remote terminal units, Programmable logic controller, and analytical instrumentation. Various enhancements had been made in the field of SCADA as from 1st generation to 4TH i.e. Monolithic, Distributed, Networked, and Internet of Things.
Read More -
Industrial Automation
The word “Industrial automation” implies automatically working organizations, which make use programmable logic controllers (PLC). Process control is a branched statistics and engineering discipline that deals with various controlling methods of output for a specific industrial automated process (architecture, controlling). It was a replacement invented the systems that required numbers of timers; relays etc and increase the cost also. PLCs are a combine package of multiple inputs and outputs, operating under various temperature ranges, even have immunity to noise. As the enhancements made year and year over, sequential relay control, motion control, process control, distributed control systems and networking are included into PLC. The main difference from other computers is that PLCs operate in industrial environments and have multiple (I/O) terminals; those connect the PLC to sensors and actuators. PLCs measure, continuously varied analog input process variables (P, T), and outputs t
Read More -
Industrial Automation using PLC, SCADA, HMI and Drives
The word “Industrial automation” implies automatically working organizations, which make use programmable logic controllers (PLC). Process control is a branched statistics and engineering discipline that deals with various controlling methods of output for a specific industrial automated process (architecture, controlling). It was a replacement invented the systems that required numbers of timers; relays etc and increase the cost also. SCADA is Supervisory Control and Data Acquisition is the systems used to control and Monitor small number of Equipments. They are basically used to perform data collection. It is a collection of HMI (human–machine interface) lock-out tag-out, Remote terminal units, Programmable logic controller, and analytical instrumentation. Various enhancements had been made in the field of SCADA as from 1st generation to 4TH i.e. Monolithic, Distributed, Networked, and Internet of Things.
Read More